Contact Us

Home > Error The > Cacti Install Spine

Cacti Install Spine


Once again, things are finally working, so thank-you very very much to tweedledee, and of course, to remmelt for creating this guide in the first place. What should be the path to your fancontrol config file (/etc/fancontrol)? I have written down what i did in my blog for my references in future. Can not continue WARNING: Cron is out of sync with the Poller Interval! weblink

ISA bus access is faster, but you need to load an additional driver module for it. but.. Fan speed is still constant. Keep your skills current with LearnDevNow - 3,200 step-by-step video tutorials by Microsoft MVPs and experts.

Cacti Install Spine

Evil DaxDecember 21st, 2007, 05:46 PMsince Gutsy I'm unable to get it running at startup, while Feisty and Edgy worked smoothly... That often includes address 0x69 (clock chip). In particular, when I try to add set fan1_div 4 as specified, I get ~$ sudo sensors -s Error: Line 2196: Unknown feature name lm85-i2c-0-2e: No such feature known I understand

As you are not root, we shall skip this step. Probing for `National Semiconductor LM78-J' Trying address 0x0290... Probing for `ITE IT8712F' Trying address 0x0290... I does however set a .pid-file in /var/run/ since it complains about it when i try to start manually.

does the script start every time the system boots up? Spine Poller File Path extract package # tar -xzvf cacti-spine-0.8.7c.tar.gz 2. When I upgraded to Gutsy, the names of the devices changed, so the old fancontrol settings did not work. My Problem is with devices other than localhost.

The fancontrol script can automatically respond to temperature changes of your system by changing fanspeeds. ISA probes are typically a bit more dangerous, as we have to write to I/O ports to do this. Im very familiar wiht linux but, this lappy is my life and rather not kill it. Loading configuration from /etc/fancontrol ...

Spine Poller File Path

Keep pressing enter until you hear (or better: see) the fan spinning up.'s-Poller-is-Not-Running-Graphs-Not-Generating-Graphing-Data-because-No-RRD-files-have-been-created-via-Poller.html Add the line fanX_div 4 near the start of your chipset config. Cacti Install Spine I ensured my /etc/crontab was calling the poller every 5 mins and i was off and away. Cacti Spine speed was 3245 now 5037 no correlation No correlations were detected.

Then run sudo modprobe w83627thf reset=1 and try pwmconfig again. have a peek at these guys Thank you! There is either no fan connected to the output of 9191-0290/pwm3, or the connected fan has no rpm-signal connected to one of the tested fan sensors. (Note: not all motherboards have Pwmconfig should now work as expected.

The names all look alike, so make sure the one you are editing is yours. It can kill your CPU if you aren't careful. Servers need all the cooling they can get, plus they are usually stored in places where no-one can hear the noise they make. check over here I don't have the time right now!

Can someone help me? Subscribe to our monthly newsletter for tech news and trends Membership How it Works Gigs Live Careers Plans and Pricing For Business Become an Expert Resource Center About Us Who We libosNovember 4th, 2007, 01:17 PMWas going to reply you. :) Yes, the fan speeds up.

The fan can run so slowly and quietly, because it's a large 12 cm fan made by Zalman (it's the 7000B AlCu).

Please verify that all fans have returned to their normal speed. Set crontab time for 1 minutes * * * * * /usr/bin/php /srv/www/htdocs/cacti/poller.php > /dev/null 2>&1 2. Backup: $ sudo cp /usr/sbin/pwmconfig /usr/sbin/pwmconfig_original Open pwmconfig: $ sudo gedit /usr/sbin/pwmconfig and go to line 68. To make the sensors modules behave correctly, add these lines to /etc/modules: #----cut here---- # I2C adapter drivers i2c-sis96x i2c-isa # I2C chip drivers eeprom it87 #----cut here---- Do you want

If you do not want to do this hit control-C now!!! Leave a Reply Cancel reply Enter your comment here... Tried "chmod 644 /sys/bus/i2c/devices/0-002e/*enable*" and pwmconfig ran without complaint, but to no effect (fans did not appear to stop/start when tested). this content Select fan output to configure, or other action: 1) Change INTERVAL 3) Save and quit 2) Just quit 4) Show configuration select (1-n): 4 Common Settings: INTERVAL=10 Any idea how I

If not, you won't be able to open any /dev/i2c-* file. Sometimes, a chip is available both through the ISA bus and an I2C bus. If you are not comfortable with doing this, don't! Jeremy on July 27, 2009 at 5:32 pm said: I did what Bruno suggested and it fixed the problem for me.

On the other hand, most companies value the data on the drives more than the hardware. This is usually safe though. When configured to use spine, if I run /usr/local/php/bin/php poller.php then spine works fine and is able to update the rra files. I wonder if I need to create one myself, however I don't think that would be a good idea given my level of knowledge and the danger of permanently frying my

linux dhcp peizhi roc 关于Unix文件的软链接 求教这个命令什么意思,我是新... If you have patched your kernel and have some drivers built in, you can safely answer NO if asked to load some modules. Join Now For immediate help use Live now! All rights reserved. 3. thanks -kartik Top TheWitness Post subject: Posted: Wed Nov 14, 2007 7:22 am Developer Joined: Tue May 14, 2002 5:08 pmPosts: 14862Location: MI, USA Of course this is Looks like this is not the case. Let the script run until you see "Select fan output to configure, or other action:" (all default options are fine, you can basically enter you way through the script).

Exiting. 说明是spine这个工具有错误 # /usr/local/spine/bin/spine 测试spine 07/07/2013 02:50:06 PM - SPINE: Poller[0] FATAL: Unable to read configuration (Spine init) 根据输出,说明其配置文件有错误,发现没有修改配置文件名字 # mv /usr/local/spine/etc/spine.conf.dist /usr/local/spine/etc/spine.conf # /usr/local/spine/bin/spine 再次测试spine,输出正常 SPINE: Using spine config file Thanks for helping... Also, as stated, if you aren't a 110% sure of what you are doing, don't try this. Rest is handled by cacti.

To switch fan though modes?